Service ABS, Service Traction Control, Service Active Handling
04-27-2010, 11:35 AM
#62
Drifting
harrell3us,
here is the guide for checking codes & resetting warning light:
with the key in the on position, but the engine not running
push and release the reset button until all messages cleared
next push and HOLD button #4
next push and release button #1 four times while holding button #4
When first engaged the on-board diagnostics go into an "automatic" mode which shows all parameters: PCM-TCS-RTD-BCM-IPC-radio-HVAC-LDCM-RDCM-SCM-RFA. If there are no problems, you will see "no more codes" on the ICP display. The computer will show two kinds of codes, "current" and "history," designated "C" or "H". A current code indicates a malfunction is present in the system whose module is displaying data. A history code indicates a past problem. When the screen displays "manual diagnostics," select the desired module by pressing the "options" button to go forward or the "trip" button to go back. Press "gages" to go forward or "fuel" to go back. To exit the diagnostic mode at any time, press "E/M".
If you want to erase or "clear" codes, press .""reset
here is the guide for checking codes & resetting warning light:
with the key in the on position, but the engine not running
push and release the reset button until all messages cleared
next push and HOLD button #4
next push and release button #1 four times while holding button #4
When first engaged the on-board diagnostics go into an "automatic" mode which shows all parameters: PCM-TCS-RTD-BCM-IPC-radio-HVAC-LDCM-RDCM-SCM-RFA. If there are no problems, you will see "no more codes" on the ICP display. The computer will show two kinds of codes, "current" and "history," designated "C" or "H". A current code indicates a malfunction is present in the system whose module is displaying data. A history code indicates a past problem. When the screen displays "manual diagnostics," select the desired module by pressing the "options" button to go forward or the "trip" button to go back. Press "gages" to go forward or "fuel" to go back. To exit the diagnostic mode at any time, press "E/M".
If you want to erase or "clear" codes, press .""reset
Where is Button #1 and Button #4 ???
And where is the "E/M" button??
Thanks!
04-27-2010, 01:14 PM
#64
Drifting
Bill,
I'm getting the C1233 code (right front wheel circuit open or shorted). I've replaced the hub and still get the code. One thing I did learn here is using an aftermarket hub instead of an OEM hub. After installing the aftermarket hub I still had the code but you could shake the wheel back and forth (indicating a crappy bearing). I checked continuity across the two sensors and the OEM was within spec. (wish I had done this before I bought the aftermarket hub but I bought the hub before I bought my service manuals). Looks as if it's pointing back to the EBCM module. This car only has 22K miles on the clock!
Could you please email me your write up? bmfvette@gmail.com
Thanks in advance!
Steve
I'm getting the C1233 code (right front wheel circuit open or shorted). I've replaced the hub and still get the code. One thing I did learn here is using an aftermarket hub instead of an OEM hub. After installing the aftermarket hub I still had the code but you could shake the wheel back and forth (indicating a crappy bearing). I checked continuity across the two sensors and the OEM was within spec. (wish I had done this before I bought the aftermarket hub but I bought the hub before I bought my service manuals). Looks as if it's pointing back to the EBCM module. This car only has 22K miles on the clock!
Could you please email me your write up? bmfvette@gmail.com
Thanks in advance!
Steve
04-27-2010, 07:36 PM
#66
Burning Brakes
I hate to do this, you must be tired of getting asked. However if you possibly could send this info. to me also I would greatly appreciate it. It seems so many have this same problem. I have a 98 C5. Here is my e-mail address hdc5lvh@sympatico.ca
Thak you!
Thak you!
Last edited by harleyvette; 04-27-2010 at 07:38 PM. Reason: wrong spelling
04-27-2010, 07:43 PM
#67
Race Director
Member Since: Aug 2000
Location: Scarborough ME
Posts: 11,188
Likes: 0
Received 0 Likes
on
0 Posts
04-28-2010, 04:39 PM
#70
1st Gear
Member Since: Apr 2010
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
04-28-2010, 04:50 PM
#71
04-28-2010, 11:12 PM
#72
Racer
Member Since: Mar 2007
Location: Down in the west Texas town of El Paso TX
Posts: 401
Likes: 0
Received 0 Likes
on
0 Posts
I would like a copy also. rarmijo001@elp.rr.com
My car has not displayed this yet, but it seems from all the requests, I am due for it to happen.
Thanks Bill
My car has not displayed this yet, but it seems from all the requests, I am due for it to happen.
Thanks Bill
04-29-2010, 03:24 AM
#74
04-29-2010, 02:54 PM
#76
Mr. Bill,
On occassion I have gotten those DIC's messages...BUT it has always been at the dragstrip with my linelock on and cleaning the rear tires coming out of the water box.
Front wheels not turning and rear tires turning like mad
was this the cause you think?
Thanks in advance
Jim
On occassion I have gotten those DIC's messages...BUT it has always been at the dragstrip with my linelock on and cleaning the rear tires coming out of the water box.
Front wheels not turning and rear tires turning like mad
was this the cause you think?
Thanks in advance
Jim
04-29-2010, 04:19 PM
#77
Safety Car
TRUSSME, you are a good man! 
04-29-2010, 05:12 PM
#78
Burning Brakes
Member Since: Jan 2006
Location: Magnolia Greens NC
Posts: 1,170
Likes: 0
Received 25 Likes
on
8 Posts
Mr. Bill,
On occassion I have gotten those DIC's messages...BUT it has always been at the dragstrip with my linelock on and cleaning the rear tires coming out of the water box.
Front wheels not turning and rear tires turning like mad
was this the cause you think?
Thanks in advance
Jim
On occassion I have gotten those DIC's messages...BUT it has always been at the dragstrip with my linelock on and cleaning the rear tires coming out of the water box.
Front wheels not turning and rear tires turning like mad
was this the cause you think?
Thanks in advance
Jim
04-29-2010, 09:02 PM
#79
1st Gear
Member Since: Apr 2010
Location: FLW MO
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
ABS service, Service Traction Control, Service Act Handling
Purchased a hub and it was replaced Service lights were still on. The servicers did a wiring check and the ground on the sensor connected to the harness on the hub was rubbed through. So you can get on lift and look at the wiring harness on the drivers side front wheel to see if any wires are frayed or broken first.
05-03-2010, 11:53 AM
#80
Cruising
Member Since: Jun 2008
Location: LALA LAND CA
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
Codes
Hi Bill, would you mind sending me the file too. =) . dinand7@hotmail.com . Thank you much.
I have recently fixed the slave cylinder for the clutch system and replaced my brakes for '06 Z51. And But this codes popped up before I did the work.
I have recently fixed the slave cylinder for the clutch system and replaced my brakes for '06 Z51. And But this codes popped up before I did the work.